一、初始露點以及紫外線照射

1、 Initial dew point and UV irradiation

這是兩種為基礎的檢測方式，在檢測時需要專屬的設備對丁基膠涂布機內的空氣干燥性，影響視線的有機發揮物進行檢查與測定。當在規定的條件中，露點小于或等于-40度，玻璃內沒有霧狀，油狀或者其他污物時方為合格。

These are two basic detection methods that require dedicated equipment to inspect and measure the air dryness inside the butyl adhesive coating machine, as well as organic compounds that affect vision. When the dew point is less than or equal to -40 degrees and there is no mist, oil or other dirt inside the glass under the specified conditions, it is considered qualified.

二、密封檢驗

2、 Sealing inspection

這種檢驗方式主要是應用在玻璃設備密封膠是否存在泄漏，且軟硬程度是否達標的情況。在進行密封檢查時，需要樣品在10±0.5KPA條件下保持2.5H厚度的增長偏差小于15%。當超過這個數值時則記為不合格。

This inspection method is mainly applied to check whether there is any leakage in the sealant of glass equipment and whether the softness and hardness meet the standard. When conducting a sealing inspection, the sample needs to maintain a 2.5H thickness growth deviation of less than 15% under the condition of 10 ± 0.5KPA. When this value is exceeded, it is considered unqualified.

三、氣候循環的檢驗

3、 Verification of climate cycle

在檢驗是需要丁基膠涂布機經歷一年四季的模擬氣候，期間需要加熱，自然冷卻以及強制制冷的操作，從而檢測玻璃在不同氣候下綜合性能。

In the inspection, the butyl adhesive coating machine needs to undergo simulated climate throughout the year, during which heating, natural cooling, and forced cooling operations are required to test the comprehensive performance of the glass in different climates.

第四、高溫高濕實驗

Fourth, High temperature and high humidity experiment

這種檢驗方式的檢驗是對密封膠的粘結力，水汽透過率以及分子篩的吸附能力的檢測，實驗時需要空氣濕度大于95%，溫度在25-55度之間，它通過循環實驗時中空玻璃內的氣體被壓縮和膨脹后的漏氣情況來判斷粘結力，水汽透過率是否達標。

This inspection method is used to test the adhesive strength, water vapor permeability, and adsorption capacity of the molecular sieve of the sealant. During the experiment, the air humidity should be greater than 95% and the temperature should be between 25-55 degrees. It determines whether the adhesive strength and water vapor permeability meet the standard by analyzing the leakage of compressed and expanded gas inside the hollow glass during the cyclic experiment.

本文由中空玻璃加工設備提供幫助，更多的相關內容請點擊： http://www.ttkjhz.net希望本文能夠?yàn)槟鷰?lái)幫助，感謝您的閱讀！

This article is provided by insulated glass processing equipment for assistance. For more related content, please click: http://www.ttkjhz.net I hope this article can be helpful to you. Thank you for reading!