鋁框上出現不沾膠現象 ：

　　Non stick phenomenon on aluminum frame:

　　檢查膠缸和膠頭的溫度是否正常，壓力是否在設定范圍內。

　　Check if the temperature of the rubber cylinder and rubber head is normal, and if the pressure is within the set range.

　　檢查兩膠頭之間的距離是否過大，確保鋁條能夠從兩個打膠頭之間通過。

　　Check if the distance between the two glue heads is too large to ensure that the aluminum strip can pass between the two glue heads.

　　如果上述情況正常，可能是打膠頭內有雜質堵塞出膠眼，需要卸下打膠頭，用煤油浸泡并清理干凈后再裝上。

　　If the above situation is normal, it may be due to impurities blocking the glue hole inside the glue head. The glue head needs to be removed, soaked in kerosene, cleaned, and then reinstalled.

　　液壓系統漏油 ：

　　Hydraulic system oil leakage:

　　設備采用液壓系統，所有連接處均由組合墊密封，若發現漏油，應及時更換組合墊。

　　The equipment adopts a hydraulic system, and all connections are sealed with composite gaskets. If oil leakage is found, the composite gaskets should be replaced in a timely manner.

　　加熱系統異常 ：

　　Abnormal heating system:

　　膠頭加熱和膠缸加熱由加熱棒和加熱盤提供，溫控表設定和調整溫度。若溫度升不高或升高后下降，檢查加熱棒或加熱盤是否損壞，溫控表是否正常。

　　The heating of the rubber head and the rubber cylinder are provided by heating rods and heating plates, and the temperature is set and adjusted by a temperature control meter. If the temperature does not rise or decreases after rising, check whether the heating rod or heating plate is damaged, and whether the temperature control meter is normal.

　　檢查加熱器熱電偶是否損壞，必要時更換。

　　Check if the heater thermocouple is damaged and replace it if necessary.

　　膠嘴漏膠 ：

　　Leakage of glue nozzle:

　　關閉涂布機，取下漏膠的膠嘴進行清洗，使用清水或其他清洗劑徹底清除內部膠水后重新安裝。

　　Turn off the coating machine, remove the leaking glue nozzle for cleaning, thoroughly remove the internal glue with water or other cleaning agents, and reinstall.

　　如果清洗后仍漏膠，可能是膠嘴損壞，需要更換。

　　If the glue still leaks after cleaning, it may be due to damage to the glue nozzle and needs to be replaced.

　　調整涂膠壓力，確保壓力適中，避免過大或過小。

　　Adjust the adhesive pressure to ensure it is moderate and avoid being too high or too low.

　　檢查膠管是否老化或損壞，必要時更換。

　　Check if the hose is aging or damaged, and replace it if necessary.

　　觸摸屏不顯示 ：

　　Touch screen not displaying:

　　檢查保險絲是否熔斷，及時更換。

　　Check if the fuse is blown and replace it promptly.

　　油缸不退缸或不進缸 ：

　　The oil cylinder does not retract or enter the cylinder:

　　檢查油缸內泄情況，必要時維修或更換。

　　Check the leakage inside the oil cylinder and repair or replace it if necessary.

　　檢查增壓泵兩端機械閥是否卡住，清理或更換。

　　Check if the mechanical valves at both ends of the booster pump are stuck, clean or replace them.

　　系統壓力異常 ：

　　Abnormal system pressure:

　　檢查增壓泵工作狀態，確保油缸到位后增壓泵停止工作。

　　Check the working status of the booster pump and ensure that the booster pump stops working after the oil cylinder is in place.

　　自動狀態下的出膠異常 ：

　　Abnormal glue dispensing in automatic mode:

　　檢查加熱定時設置，確保在自動狀態下溫度和壓力均正常。

　　Check the heating timing settings to ensure that the temperature and pressure are normal in automatic mode.

　　檢查膠嘴間距是否合適，維修或更換。

　　Check if the spacing between the rubber nozzles is appropriate, repair or replace them.

　　清理氣路，確保氣路正常工作。

　　Clean the air circuit to ensure its normal operation.

　　建議定期對設備進行維護和檢查，及時發現并解決故障，以保證全自動丁基膠涂布機的正常運行和生產質量。

　　It is recommended to regularly maintain and inspect the equipment, promptly detect and solve faults, to ensure the normal operation and production quality of the fully automatic butyl rubber coating machine.

　　有了上面的小總結，希望對廣大客戶有所幫助，如果有什么不理解的或者尋求幫助的請點擊我們的網站：http://www.ttkjhz.net或者來電咨詢，我們會盡全力為您解決

　　With the above summary, we hope it can be helpful to our customers. If you have any questions or need help, please click on our website: http://www.ttkjhz.net Or call us for consultation, we will do our best to solve it for you