
中空玻璃丁基膠涂布機常見故障排除方法
時間:2025-11-19 來源:http://www.ttkjhz.net/ 發布人:昌盛機械
中空玻璃丁基膠涂布機常見問題的解決方法:
Solution to common problems of butyl rubber coating machine for insulating glass:
1.鋁框上出現一邊或兩邊都不沾膠的現象時
When there is no adhesive on one or both sides of the aluminum frame
首先我們應檢查膠缸、膠頭的溫度是否正常,壓力是否在我們?cè)O(shè)定的范圍之內,檢查兩膠頭的距離是否過大(此距離設定至鋁條剛剛能從兩個打膠頭之間過去為最好)。
Firstly, we should check whether the temperature of the glue cylinder and glue head is normal, whether the pressure is within the range we set, and whether the distance between the two glue heads is too large (this distance should be set to the point where the aluminum strip can just pass between the two glue heads).
如果上述情況都沒有問題,可斷定兩個打膠頭(或一個),由于丁基膠中有雜質而堵住了膠頭出膠的眼,這就需要卸下打膠頭,用煤油浸泡,然后將膠頭內的膠全部清理干凈后再裝上即可。
If the above situations are not a problem, it can be concluded that two or one of the glue heads have blocked the glue outlet due to impurities in the butyl rubber. This requires removing the glue head, soaking it in kerosene, and then cleaning all the glue inside the glue head before reinstalling it.
2.該設備全部采用液壓系統,油缸及液壓系統全部采用高壓油管連接,每個連接處都由組合墊密封,若發現漏油,及時更換組合墊。
2. The equipment adopts a hydraulic system, and the oil cylinder and hydraulic system are all connected by high-pressure oil pipes. Each connection is sealed with a combination gasket. If oil leakage is found, the combination gasket should be replaced in a timely manner.
3.該設備的膠頭加熱和膠缸加熱,由加熱棒兩個和加熱盤一個提供,由溫控表來設定和調整溫度的高低,若發現溫度升不高或升高后往下降,請檢查加熱棒或加熱盤是否損壞,并檢查溫控表是否正常。
3. The heating of the rubber head and the heating of the rubber cylinder of the device are provided by two heating rods and one heating plate, and the temperature is set and adjusted by a temperature control meter. If the temperature does not rise or decreases after rising, please check whether the heating rod or heating plate is damaged and whether the temperature control meter is normal.
本文由 中空玻璃丁基膠涂布機 友情奉獻.更多有關的知識請點擊 http://www.ttkjhz.net/ 真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.
This article is a friendly contribution from the hollow glass butyl rubber coating machine For more related knowledge, please click http://www.ttkjhz.net/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.
- 中空玻璃丁基膠涂布機常見故障排除方法 2025/11/19
- 雙組份打膠機打膠不飽滿怎么解決? 2025/11/18
- 全自動鋁條折彎的折彎尺寸不準怎么回事 2025/11/17
- 全自動封膠線中中板壓與棍壓的區別 2025/11/15
- 中空玻璃加工設備?故障分析流程 2025/11/14
- 中空玻璃生產線:中空玻璃生產流程及所需要設備 2025/11/13
- 丁基膠涂布機液壓油的選擇指南 2025/10/31
- 玻璃涂布機設備操作流程 2025/10/30
- 雙組份打膠機比例怎么調 2025/10/29
- 全自動鋁條折彎?rùn)C(jī)折彎角度偏差的解決方法 2025/10/29
產品分類Product categories
聯系我們Contact us
- 咨詢熱線:0531-85717458 13705446998
- 公司地址: 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們:

當前位置:



