91在线观看免费,一区二区三区日韩精品,国产三级精品三级

當前位置：首頁-新聞資訊-企業新聞

丁基膠涂布機常見問題的解決方法

時間：2022-10-12 來源：http://www.ttkjhz.net/ 發布人：昌盛機械

丁基膠涂布機常見問題的解決方法，希望能幫到大家。

Butyl rubber coater common problems of solutions, I hope to help you.

1.鋁框上出現一邊或兩邊都不沾膠的現象時

1. When one or both sides of the aluminum frame are free of glue

**我們應檢查膠缸、膠頭的溫度是否正常，壓力是否在我們?cè)O(shè)定的范圍之內，檢查兩膠頭的距離是否過大（此距離設定至鋁條剛剛能從兩個打膠頭之間過去為較好）。

**We should check whether the temperature of the rubber cylinder and rubber head is normal, whether the pressure is within the range we set, and whether the distance between the two rubber heads is too large (it is better to set this distance until the aluminum bar can just pass between the two rubber heads).

如果上述情況都沒有問題，可斷定兩個打膠頭（或一個），由于丁基膠中有雜質而堵住了膠頭出膠的眼，這就需要卸下打膠頭，用煤油浸泡，然后將膠頭內的膠全部清理干凈后再裝上即可。

If there is no problem in the above situations, it can be concluded that two rubber applicators (or one) have blocked the rubber outlet of the rubber applicator due to impurities in butyl rubber, so it is necessary to remove the rubber applicator, soak it in kerosene, clean all the rubber in the rubber applicator, and then install it.

2.該設備全部采用液壓系統，油缸及液壓系統全部采用高壓油管連接，每個連接處都由組合墊密封，若發現漏油，及時更換組合墊。

2. The equipment adopts hydraulic system, and the oil cylinder and hydraulic system are connected by high-pressure oil pipe. Each connection is sealed by a combination gasket. If oil leakage is found, the combination gasket shall be replaced in time.

3.該設備的膠頭加熱和膠缸加熱，由加熱棒兩個和加熱盤一個提供，由溫控表來設定和調整溫度的高低，若發現溫度升不高或升高后往下降，請檢查加熱棒或加熱盤是否損壞，并檢查溫控表是否正常。

3. The rubber head heating and rubber cylinder heating of the equipment are provided by two heating rods and one heating plate. The temperature is set and adjusted by the temperature control meter. If the temperature does not rise or drops after rising, please check whether the heating rod or heating plate is damaged and whether the temperature control meter is normal.

以上就是為大家介紹的有關丁基膠涂布機的詳細的介紹,希望對您有所幫助.

The above is a detailed introduction of butyl rubber coating machine, and we hope it will be helpful to you. If you have any questions, please contact us.

上一篇：鋁條丁基膠涂布機的簡單介紹 下一篇：如何正確的使用中空玻璃打膠機？

相關新聞 more+